Difficulty
Moderate
Steps
18
Time Required
25 minutes
Sections
3
- Back Panel
- 8 steps
- Front Panel
- 5 steps
- Daughter Board
- 5 steps
Flags
0
BackCanon EOS Rebel XSi / 450D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Panel
- Squeeze the eyepiece between your index finger and thumb and lift up and off.
Squeeze the eyepiece between your index finger and thumb and lift up and off.
1024
Step 2
- Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera.
Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera.
Step 3
- Using the PH000 screwdriver head, remove the two 3mm screws on the right side of the camera (from the LCD screen).
Using the PH000 screwdriver head, remove the two 3mm screws on the right side of the camera (from the LCD screen).
Step 4
- Remove grip by slowly peeling off.
Remove grip by slowly peeling off.
Step 5
- Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece.
Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece.
Step 6
- Using the PH000 screwdriver head, remove one 4 mm screw on the left side of the camera (from the LCD screen).
Using the PH000 screwdriver head, remove one 4 mm screw on the left side of the camera (from the LCD screen).
Step 7
- Remove the side panel by lifting off with fingers.
Remove the side panel by lifting off with fingers.
Step 8
- Use hands to pry off the back panel.
Use hands to pry off the back panel.
Step 9
Front Panel
- Using the PH000 screwdriver head, remove the four 3mm screws on the front
Using the PH000 screwdriver head, remove the four 3mm screws on the front
Step 10
- Remove front grip by gently peeling from the edge towards the center of the camera
Remove front grip by gently peeling from the edge towards the center of the camera
Step 11
- Using the PH000 screwdriver head, unscrew the 3 mm screw that was under the grip
Using the PH000 screwdriver head, unscrew the 3 mm screw that was under the grip
Step 12
- Using the PH000 screwdriver, remove the 4mm screw at the bottom of the camera
Using the PH000 screwdriver, remove the 4mm screw at the bottom of the camera
Step 13
- Remove the front panel by using tweezers to pry the panel over the metal ring protrusion
Remove the front panel by using tweezers to pry the panel over the metal ring protrusion
Step 14
Daughter Board
- Using the PH000 screwdriver head, remove the three 3mm screws
Using the PH000 screwdriver head, remove the three 3mm screws
Step 15
- Carefully remove the cable from its plastic base with fingers
Carefully remove the cable from its plastic base with fingers
Step 16
- Gently slide board out with thumb
Gently slide board out with thumb
Step 17
- Gently disconnect cable by pulling out from plastic base with fingers
Gently disconnect cable by pulling out from plastic base with fingers
Step 18
- Disconnect cables by pulling out from base with fingers
Disconnect cables by pulling out from base with fingers
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Erik Mork
Member since: 01/27/2017
596 Reputation
5 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 22-10, Maness Winter 2017
Member of Cal Poly, Team 22-10, Maness Winter 2017
CPSU-MANESS-W17S22G10
4 Members
10 Guides authored
djratlif - Jul 31, 2019
Reply
what does this fix
