Difficulty

Moderate

Steps

14

Time Required

                          20 - 30 minutes

Sections

2

  • Back Panel
  • 8 steps
  • Mother Board
  • 6 steps

Flags

0

  • BackCanon EOS Rebel XSi / 450D

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The back panel must be removed to access this component.

Remove the battery before beginning.

What you need

Step 1

              Back Panel
  • Squeeze the eyepiece between your index finger and thumb and lift up and off.

Squeeze the eyepiece between your index finger and thumb and lift up and off.

1024

Step 2

  • Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera.

Using the PH000 screwdriver head, remove the four 4 mm screws on the bottom of the camera.

Step 3

  • Using the PH000 screwdriver head, remove the two 3mm screws on the right side of the camera (from the LCD screen).

Using the PH000 screwdriver head, remove the two 3mm screws on the right side of the camera (from the LCD screen).

Step 4

  • Remove grip by slowly peeling off.

Remove grip by slowly peeling off.

Step 5

  • Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece.

Using the PH000 screwdriver, remove the four 4mm screws behind the eyepiece.

Step 6

  • Using the PH000 screwdriver head, remove one 4 mm screw on the left side of the camera (from the LCD screen).

Using the PH000 screwdriver head, remove one 4 mm screw on the left side of the camera (from the LCD screen).

Step 7

  • Remove the side panel by lifting off with fingers.

Remove the side panel by lifting off with fingers.

Step 8

  • Use hands to pry off the back panel.

Use hands to pry off the back panel.

Step 9

              Mother Board
  • Using the PH00 screwdriver head, unscrew the three 3mm screws.

Using the PH00 screwdriver head, unscrew the three 3mm screws.

Step 10

  • Disconnect the five cables attached to the motherboard by gently pulling with tweezers.

Disconnect the five cables attached to the motherboard by gently pulling with tweezers.

Step 11

  • Remove tab from base by lifting up with finger.

Remove tab from base by lifting up with finger.

Step 12

  • Using the PH00 screwdriver head, unscrew the three 3mm screws on the left side of the camera.

Using the PH00 screwdriver head, unscrew the three 3mm screws on the left side of the camera.

Step 13

  • Using the PH00 screwdriver head, unscrew the last 4mm screw from the motherboard.

Using the PH00 screwdriver head, unscrew the last 4mm screw from the motherboard.

Step 14

  • Remove motherboard by gently lifting out with fingers.

Remove motherboard by gently lifting out with fingers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 8 other contributors 


                    Erik Mork

Member since: 01/27/2017

596 Reputation

                                      5 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 22-10, Maness Winter 2017                        

                                                  Member of Cal Poly, Team 22-10, Maness Winter 2017 



                    CPSU-MANESS-W17S22G10                     


                                            4 Members                     


                                            10 Guides authored