Difficulty
Moderate
Steps
13
Time Required
15 - 20 minutes
Sections
4
- Battery
- 3 steps
- Memory Card
- 3 steps
- Top Casing
- 4 steps
- Snapshot Button
- 3 steps
Flags
1
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackCanon EOS Rebel XTi / 400D
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place the camera upside down, and position it to where the back of the camera is visible.
Place the camera upside down, and position it to where the back of the camera is visible.
1024
Step 2
- Pull the orange tab to the right to release the primary battery.
Pull the orange tab to the right to release the primary battery.
Step 3
- To remove the secondary battery, reposition the camera to where the display screen is facing upwards.
- Place your finger inside the empty battery compartment and pull away from the camera on the ridged battery tab.
To remove the secondary battery, reposition the camera to where the display screen is facing upwards.
Place your finger inside the empty battery compartment and pull away from the camera on the ridged battery tab.
Step 4
Memory Card
- Place the camera on its side with the soft touch grip facing up and the top of the camera facing right.
Place the camera on its side with the soft touch grip facing up and the top of the camera facing right.
Step 5
- Slide the memory card door in the direction of the arrow engraved on the camera.
- Once the door has slid open to its full position, lift up on the door.
Slide the memory card door in the direction of the arrow engraved on the camera.
Once the door has slid open to its full position, lift up on the door.
Step 6
- With the door open, push down the small black plunger next to the CF slot. The CF card will disengage from the slot and be ejected far enough that you can grasp it between thumb and forefinger and remove it from the slot.
- The plunger will stay in its depressed position until a CF card is again inserted in the slot.
With the door open, push down the small black plunger next to the CF slot. The CF card will disengage from the slot and be ejected far enough that you can grasp it between thumb and forefinger and remove it from the slot.
The plunger will stay in its depressed position until a CF card is again inserted in the slot.
Step 7
Top Casing
- Remove the single 10 mm JIS #00 shoulder screw.
- Remove the two 6 mm JIS #00 screws.
Remove the single 10 mm JIS #00 shoulder screw.
Remove the two 6 mm JIS #00 screws.
Step 8
- Separate the top casing from the electrical components enough to expose the wire harnesses that will need to be disconnected.
- Ensure to remove the casing gently. There are several wire harnesses connecting the motherboard to components on the casing.
Separate the top casing from the electrical components enough to expose the wire harnesses that will need to be disconnected.
Ensure to remove the casing gently. There are several wire harnesses connecting the motherboard to components on the casing.
Step 9
- Unplug the yellow connector located on the top of the camera.
Unplug the yellow connector located on the top of the camera.
Step 10
- Disconnect the red connector located by the USB port.
Disconnect the red connector located by the USB port.
Step 11
Snapshot Button
- Use a J00 screwdriver to remove the two silver 4 mm screws from underneath the snapshot button.
Use a J00 screwdriver to remove the two silver 4 mm screws from underneath the snapshot button.
Step 12
- Use a J00 screwdriver to remove the 3 mm screws from the plate under snapshot the snapshot button.
- Place the components off to the side without removing any ribbons.
- Be careful as ribbon cables are fragile and may rip easily.
Use a J00 screwdriver to remove the 3 mm screws from the plate under snapshot the snapshot button.
Place the components off to the side without removing any ribbons.
Be careful as ribbon cables are fragile and may rip easily.
Step 13
- Use a 1.5 flat head bit to remove the c-clip from underneath the snapshot button by pushing against the open side of the pin.
Use a 1.5 flat head bit to remove the c-clip from underneath the snapshot button by pushing against the open side of the pin.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Luis Calle
Member since: 08/30/2015
401 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 8-6, Eyestone Fall 2015
Member of USF Tampa, Team 8-6, Eyestone Fall 2015
USFT-EYESTONE-F15S8G6
3 Members
18 Guides authored
