Difficulty

Easy

Steps

7

Time Required

                          15 - 30 minutes

Sections

3

  • Front Paneling
  • 3 steps
  • Right Side Paneling
  • 1 step
  • Speaker
  • 3 steps

Flags

1

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackCanon ImageCLASS MF4350d

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Front Paneling
  • Lift the printer lid up as shown in the photo.

Lift the printer lid up as shown in the photo.

1024

Step 2

  • Locate and remove the two 10mm side screws. There is one on each side.

Locate and remove the two 10mm side screws. There is one on each side.

Step 3

  • Unhook the plastic panel from the printer starting from the top.
  • You may need to wiggle the panel a bit to loosen it.
  • To remove the bottom part of the paneling gently lay the printer on its back.
  • The scanner lid needs to be supported when moving the printer

Unhook the plastic panel from the printer starting from the top.

You may need to wiggle the panel a bit to loosen it.

To remove the bottom part of the paneling gently lay the printer on its back.

The scanner lid needs to be supported when moving the printer

Step 4

              Right Side Paneling
  • Gently unhook the right side paneling (as looking at the printer’s front face) from the printer.
  • Use a gentle back and forth motion to wiggle the hooks out.

Gently unhook the right side paneling (as looking at the printer’s front face) from the printer.

Use a gentle back and forth motion to wiggle the hooks out.

Step 5

              Speaker
  • Lay printer on its left side for better access to the speaker.
  • Note: The scanner lid needs to be supported when moving the printer

Lay printer on its left side for better access to the speaker.

Note: The scanner lid needs to be supported when moving the printer

Step 6

  • Locate the black 7mm screw holding the speaker in place.
  • Using a Phillips head screw driver, unscrew the 7mm screw.

Locate the black 7mm screw holding the speaker in place.

Using a Phillips head screw driver, unscrew the 7mm screw.

Step 7

  • Locate the red and black wires connected to the speaker.
  • Undo the white clip holding the wires in place by pinching the tab on the top.
  • Remove the red and black wires from the wire bundle.
  • When replacing the old speaker, do not touch any part of the new speaker that is not metal other than the wires. Doing so could damage the speaker.
  • Lift out the speaker

Locate the red and black wires connected to the speaker.

Undo the white clip holding the wires in place by pinching the tab on the top.

Remove the red and black wires from the wire bundle.

When replacing the old speaker, do not touch any part of the new speaker that is not metal other than the wires. Doing so could damage the speaker.

Lift out the speaker

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Helena Yanez

Member since: 09/29/2013

446 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 13-1, Forte Fall 2013                        

                                                  Member of Cal Poly, Team 13-1, Forte Fall 2013 



                    CPSU-FORTE-F13S13G1                     


                                            5 Members                     


                                            8 Guides authored