Canon Optura 100Mc Lcd Screen And Glass Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          20 minutes

Sections

Hand Strap
2 steps
Battery
2 steps
LCD Screen and Glass Screen
10 steps

Flags

BackCanon Optura 100MC
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Hand Strap

Orient the camera with the hand strap facing you.
Remove the two 4mm #00 Philips screws.
When the screws are removed, the black plate will easily come off as well as the two metal plates under it. Be careful to not let them fall or get lost.

Orient the camera with the hand strap facing you.

Remove the two 4mm #00 Philips screws.

When the screws are removed, the black plate will easily come off as well as the two metal plates under it. Be careful to not let them fall or get lost.

1024

Step 2

Lift the strap up.

Lift the strap up.

Step 3

              Battery

Orient the camera so that the back button panel and viewfinder are facing you.
Push the “Battery Release” button to the side and hold.

Orient the camera so that the back button panel and viewfinder are facing you.

Push the “Battery Release” button to the side and hold.

Step 4

While holding the battery release button to the side, slide the battery towards you, past the release button.

While holding the battery release button to the side, slide the battery towards you, past the release button.

Step 5

              LCD Screen and Glass Screen

Reorient camera so that the playback button panel and empty battery slot are facing you. The edge of the LCD screen should be facing you.
To open the screen, hold the open button shown down and flip the screen open.
Remove the two #00 Philips 4mm screws on the outer edge of the LCD casing.

Reorient camera so that the playback button panel and empty battery slot are facing you. The edge of the LCD screen should be facing you.

To open the screen, hold the open button shown down and flip the screen open.

Remove the two #00 Philips 4mm screws on the outer edge of the LCD casing.

Step 6

Flip the screen counter-clockwise and reorient the camera with the bottom edge of the LCD screen facing you.
Remove the 4mm #00 Phillips screw from the bottom of the LCD casing

Flip the screen counter-clockwise and reorient the camera with the bottom edge of the LCD screen facing you.

Remove the 4mm #00 Phillips screw from the bottom of the LCD casing

Step 7

Remove the two 4mm #00 Phillips screws on the inside edge of the LCD casing. After removing the first screw you will have to rotate the screen 180 degrees to remove the second screw.

Remove the two 4mm #00 Phillips screws on the inside edge of the LCD casing. After removing the first screw you will have to rotate the screen 180 degrees to remove the second screw.

Step 8

Reorient the camera with the LCD screen edge and playback button panel facing you.
Remove front panel of LCD screen by pulling it directly to the side.

Reorient the camera with the LCD screen edge and playback button panel facing you.

Remove front panel of LCD screen by pulling it directly to the side.

Step 9

Disconnect the screen components from the main body of the camcorder by applying downward pressure near the circled hinge.

Disconnect the screen components from the main body of the camcorder by applying downward pressure near the circled hinge.

Step 10

Remove the 4mm #00 Phillips screw connecting the LCD to the glass screen and lower casing.

Remove the 4mm #00 Phillips screw connecting the LCD to the glass screen and lower casing.

Step 11

Remove the lower casing by pushing up on the glass screen with your thumb.

Remove the lower casing by pushing up on the glass screen with your thumb.

Step 12

Remove the glass screen from the LCD by lifting up on the cream colored hinge to disconnect the ribbon wire. Pull the glass screen away.
Replace the glass screen if it is cracked or damaged.

Remove the glass screen from the LCD by lifting up on the cream colored hinge to disconnect the ribbon wire. Pull the glass screen away.

Replace the glass screen if it is cracked or damaged.

Step 13

Remove the LCD by disconnecting the remaining two ribbon wires by lifting up the cream-colored gate and sliding the ribbon out of the black gate.

Remove the LCD by disconnecting the remaining two ribbon wires by lifting up the cream-colored gate and sliding the ribbon out of the black gate.

Step 14

Replace the broken LCD with a new one.

Replace the broken LCD with a new one.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors

                    Jeanette Neethling

Member since: 01/19/2011

531 Reputation

                                      5 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Cal Poly, Team 1-12, Amido Winter 2011                        

                                                  Member of Cal Poly, Team 1-12, Amido Winter 2011 



                    CPSU-AMIDO-W11S1G12                     


                                            4 Members                     


                                            11 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team