Difficulty

Difficult

Steps

16

Time Required

                          30 - 35 minutes

Sections

4

  • Battery
  • 2 steps
  • Plastic Case
  • 8 steps
  • Lens
  • 5 steps
  • LCD Display
  • 1 step

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackCanon PowerShot A3400 IS

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Place thumb on area right next to where it says open and slide to the right to open.

Place thumb on area right next to where it says open and slide to the right to open.

1024

Step 2

  • Remove the battery by pushing the orange object outwards; the battery will spring up and out.

Remove the battery by pushing the orange object outwards; the battery will spring up and out.

Step 3

              Plastic Case
  • Remove the two 5.00 mm screws in the bottom of the casing with a Philips #000 screwdriver

Remove the two 5.00 mm screws in the bottom of the casing with a Philips #000 screwdriver

Step 4

  • Place the camera on to the side that has the image stabilizer label.
  • Remove the 5.00 mm screws that are on this side using the screwdriver.

Place the camera on to the side that has the image stabilizer label.

Remove the 5.00 mm screws that are on this side using the screwdriver.

Step 5

  • Place camera on to the side with the A/V Out Digital Cover facing up.
  • Remove this visible 5.00 mm screw.
  • Pull the A/V Out Digital cover back to uncover the next step.

Place camera on to the side with the A/V Out Digital Cover facing up.

Remove this visible 5.00 mm screw.

Pull the A/V Out Digital cover back to uncover the next step.

Step 6

  • Remove the 5.00 mm screw from behind the cover.

Remove the 5.00 mm screw from behind the cover.

Step 7

  • Make sure the battery cover is open.

Make sure the battery cover is open.

Step 8

  • Turn the camera onto the side with the A/V out Digital cover.
  • Use your finger to pull this tab to the right.

Turn the camera onto the side with the A/V out Digital cover.

Use your finger to pull this tab to the right.

Step 9

  • Remove the lens side by using your fingers or a spudger to pry it gently open.
  • Try to pry it loose all around that side so that it is easier to pull off.

Remove the lens side by using your fingers or a spudger to pry it gently open.

Try to pry it loose all around that side so that it is easier to pull off.

Step 10

  • Using your fingers, pull the screen side gently off.
  • Try to loosen it all around that side so that it is easier to try and pull it off.

Using your fingers, pull the screen side gently off.

Try to loosen it all around that side so that it is easier to try and pull it off.

Step 11

              Lens
  • Remove the three 5 mm screws

Remove the three 5 mm screws

Step 12

  • Pull the screen away from the main components.
  • Do not pull hard as there are some ribbons still attached to the motherboard that could be damaged if you use too much force.

Pull the screen away from the main components.

Do not pull hard as there are some ribbons still attached to the motherboard that could be damaged if you use too much force.

Step 13

  • Lift the metal plate with the plastic opening tool.

Lift the metal plate with the plastic opening tool.

Step 14

  • Remove all of these 5 mm screws

Remove all of these 5 mm screws

Step 15

  • Gently remove the lens componenet.
  • The orange flex cables are connected to ZIF connectors. Be sure to disconnect and reconnect them properly by first unlocking the retaining flap on each connector.

Gently remove the lens componenet.

The orange flex cables are connected to ZIF connectors. Be sure to disconnect and reconnect them properly by first unlocking the retaining flap on each connector.

Step 16

              LCD Display
  • Detach the Motherboard, and then gently pull the motherboard away from the screen.

Detach the Motherboard, and then gently pull the motherboard away from the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Matt Mullins

Member since: 01/13/2015

104 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       USF Tampa, Team 1-1, Sullivan Spring 2014                        

                                                  Member of USF Tampa, Team 1-1, Sullivan Spring 2014 



                    USFT-SULLIVAN-S14S1G1                     


                                            1 Member                     


                                            2 Guides authored

The Heat - Sep 2, 2017

Reply

useless if you try to do it reverse.. Don’t even try it.