Difficulty
Moderate
Steps
11
Time Required
20 - 30 minutes
Sections
2
- Back Cover
- 5 steps
- Function Key Motherboard
- 6 steps
Flags
0
BackCanon PowerShot A540
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Turn off the camera.
- Turn the camera upside-down and press the tab to release the battery cover. Remove the batteries.
Turn off the camera.
Turn the camera upside-down and press the tab to release the battery cover. Remove the batteries.
1024
Step 2
- Turn the camera upside down to view the “Card/Batt. Open” Cover.
- Use a Phillips head #000 screwdriver to remove the three (3) 4.0 mm screws.
Turn the camera upside down to view the “Card/Batt. Open” Cover.
Use a Phillips head #000 screwdriver to remove the three (3) 4.0 mm screws.
Step 3
- Open “Card/Batt. Open” Cover.
- Remove the one (1) 5.0 mm screw with the Phillips head #000 screwdriver.
Open “Card/Batt. Open” Cover.
Remove the one (1) 5.0 mm screw with the Phillips head #000 screwdriver.
Step 4
- Turn the camera to the right side of the LCD screen.
- Remove the three (3) 4.0 mm screws with the Phillips head #000 screwdriver.
Turn the camera to the right side of the LCD screen.
Remove the three (3) 4.0 mm screws with the Phillips head #000 screwdriver.
Step 5
- Gently remove the back cover.
- Start at the bottom at the corner of the “Card/Batt. Open” Cover.
- Then move onto the other edges and the top.
- It may be tight at the top!
Gently remove the back cover.
Start at the bottom at the corner of the “Card/Batt. Open” Cover.
Then move onto the other edges and the top.
It may be tight at the top!
Step 6
Function Key Motherboard
- Turn the camera to view the back.
- Remove the one (1) 3.0 mm screw on the top right corner of the screen.
- There is a small metal bar that rests on this frame. Keep it with the screws that have been removed from the camera.
Turn the camera to view the back.
Remove the one (1) 3.0 mm screw on the top right corner of the screen.
There is a small metal bar that rests on this frame. Keep it with the screws that have been removed from the camera.
Step 7
- Lift the LCD Screen off of the back to view the attached ribbon cables.
- Use tweezers to flip the black bar up.
Lift the LCD Screen off of the back to view the attached ribbon cables.
Use tweezers to flip the black bar up.
Step 8
- Gently pull the big ribbon out.
- Gently pull the small ribbon out.
- The small ribbon does not have a bar like the big ribbon.
Gently pull the big ribbon out.
Gently pull the small ribbon out.
The small ribbon does not have a bar like the big ribbon.
Step 9
- Remove the two (2) 3.0 mm screws with the Phillips head #000 screwdriver.
Remove the two (2) 3.0 mm screws with the Phillips head #000 screwdriver.
Step 10
- Remove the orange ribbon from the clamp by using a Spudger to push the bar up.
Remove the orange ribbon from the clamp by using a Spudger to push the bar up.
Step 11
- Remove the Function Key Motherboard and replace.
- There is another metal bar that comes off of the SD Card reader when screws are removed.
Remove the Function Key Motherboard and replace.
There is another metal bar that comes off of the SD Card reader when screws are removed.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Cooper Hale
Member since: 03/22/2015
532 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
Baylor, Team 7-12, Williams Spring 2015
Member of Baylor, Team 7-12, Williams Spring 2015
BU-WILLIAMS-S15S7G12
3 Members
20 Guides authored
