Difficulty
Difficult
Steps
10
Time Required
15 - 20 minutes
Sections
1
- Speaker
- 10 steps
Flags
2
Missing Prerequisites
This guide is missing information on how to start the process. Make a prerequisite guide!
Better Introduction
Improve this guide by completing or revising its introduction.
BackCanon PowerShot A610
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Speaker
- Remove the three screws attaching the side panel using a Phillips #00 screwdriver.
- Remove the side paneling from the camera.
- Remove the two remaining screws attached to the frame of the camera.
Remove the three screws attaching the side panel using a Phillips #00 screwdriver.
Remove the side paneling from the camera.
Remove the two remaining screws attached to the frame of the camera.
1024
Step 2
- Remove the two screws on the bottom panel of the camera.
Remove the two screws on the bottom panel of the camera.
Step 3
- Open the battery cover.
- Remove the four screws inside.
- One screw is located on the top side of the bottom cover. The remaining three screws are located at the bottom of the battery compartment.
- Close the battery cover.
Open the battery cover.
Remove the four screws inside.
One screw is located on the top side of the bottom cover. The remaining three screws are located at the bottom of the battery compartment.
Close the battery cover.
Step 4
- Open the “DIGITAL AV OUT” door on the camera.
- Remove the three screws.
- Remove the door from the camera.
Open the “DIGITAL AV OUT” door on the camera.
Remove the three screws.
Remove the door from the camera.
Step 5
- Gripping the sides of the top cover, gently pull apart the top cover from the camera.
- The top cover does not completely detach.
Gripping the sides of the top cover, gently pull apart the top cover from the camera.
The top cover does not completely detach.
Step 6
- Open the battery cover.
- Gently pull apart the front cover from the camera.
- This may require some force. Be careful not to break the plastic.
Gently pull apart the front cover from the camera.
This may require some force. Be careful not to break the plastic.
Step 7
- Using an opening tool, push the black attachment away from the white connection piece to detach the connector ribbon.
Using an opening tool, push the black attachment away from the white connection piece to detach the connector ribbon.
Step 8
- Remove the 3 mm screw holding the metal frame.
Remove the 3 mm screw holding the metal frame.
Step 9
- Use an unfolded paper clip to push the speaker from the top of the casing out towards the bottom.
- Use a bit of force as the speaker is glued into the top casing.
- There is a soft fabric speaker cover separating the speaker from the casing. Make sure not to remove it from its position in the housing.
Use an unfolded paper clip to push the speaker from the top of the casing out towards the bottom.
Use a bit of force as the speaker is glued into the top casing.
There is a soft fabric speaker cover separating the speaker from the casing. Make sure not to remove it from its position in the housing.
Step 10
- Desolder the speaker at the two solder points and reattach the new speaker.
Desolder the speaker at the two solder points and reattach the new speaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Matthew Ramirez
Member since: 01/20/2011
625 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 11-26, Maness Winter 2011
Member of Cal Poly, Team 11-26, Maness Winter 2011
CPSU-MANESS-W11S11G26
3 Members
9 Guides authored
