Difficulty
Moderate
Steps
11
Time Required
15 - 30 minutes
Sections
2
- Front Panel
- 7 steps
- Shooting Mode Dial
- 4 steps
Flags
0
BackCanon PowerShot A630
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front Panel
- Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera.
- Remove batteries.
Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera.
Remove batteries.
1024
Step 2
- Remove the three indicated .2mm screws using a Phillips #00 screwdriver.
- Gently pull off side-panel to remove it.
Remove the three indicated .2mm screws using a Phillips #00 screwdriver.
Gently pull off side-panel to remove it.
Step 3
- Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Step 4
- Remove the indicated .2mm screw using a Phillips #00 screwdriver.
- Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Phillips #00 screwdriver.
Remove the indicated .2mm screw using a Phillips #00 screwdriver.
Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Phillips #00 screwdriver.
Step 5
- Open ‘DIGITAL A/V OUT’ door on camera.
- Remove the two indicated .2mm screws using a Phillips #00 screwdriver.
Open ‘DIGITAL A/V OUT’ door on camera.
Step 6
- Grip the sides of the top panel and gently pull to separate the top panel from the camera body.
- The top panel will not completely detach.
Grip the sides of the top panel and gently pull to separate the top panel from the camera body.
The top panel will not completely detach.
Step 7
- Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels.
- Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.
Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels.
Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.
Step 8
Shooting Mode Dial
- Pry open the connector on the yellow ribbon cable using a plastic opening tool.
Pry open the connector on the yellow ribbon cable using a plastic opening tool.
Step 9
- Remove the 2 mm screws from the metal plate.
Remove the 2 mm screws from the metal plate.
Step 10
- Pull away the metal plate, exposing the underbelly of the mode dial.
- Be careful not to pull too hard. Metal plate should remain attached.
Pull away the metal plate, exposing the underbelly of the mode dial.
Be careful not to pull too hard. Metal plate should remain attached.
Step 11
- Remove the 2mm screw using the #00 Phillips screwdriver.
- The mode dial should fall out.
Remove the 2mm screw using the #00 Phillips screwdriver.
The mode dial should fall out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 5 other contributors
Alicia Burns
Member since: 10/13/2014
550 Reputation
5 Guides authored
Badges:
15
+12 more badges
Team
Clemson, Team 2-5, Benson Fall 2014
Member of Clemson, Team 2-5, Benson Fall 2014
CLEM-BENSON-F14S2G5
4 Members
18 Guides authored
