Difficulty
Easy
Steps
12
Time Required
5 minutes
Sections
2
- Back Cover
- 7 steps
- Front Cover
- 5 steps
Flags
3
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Better Introduction
Improve this guide by completing or revising its introduction.
BackCanon PowerShot A80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Remove the three Phillips #00 screws from the bottom of the camera.
Remove the three Phillips #00 screws from the bottom of the camera.
1024
Step 2
- Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open.
- Remove the memory card if it is still in the camera.
- Use the Phillips #00 screwdriver to remove the single screw underneath the memory card slot door.
Open the door to the CompactFlash memory card slot by sliding it towards you and swinging it open.
Remove the memory card if it is still in the camera.
Use the Phillips #00 screwdriver to remove the single screw underneath the memory card slot door.
Step 3
- Remove the Phillips #)0 screw located inside the top of the memory card compartment.
Remove the Phillips #)0 screw located inside the top of the memory card compartment.
Step 4
- Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down.
- Remove the batteries from the compartment.
- Remove the three Phillips #00 screws located inside the battery compartment.
- The screw on the left is longer than the other two.
Open the battery compartment door at the bottom of the camera by sliding the latch to the right and then sliding the door down.
Remove the batteries from the compartment.
Remove the three Phillips #00 screws located inside the battery compartment.
The screw on the left is longer than the other two.
Step 5
- You should now able to remove the top lid of the camera.
- Be cautious of the fragile mylar cable that connects the lid to the main body of the camera.
- Removing the lid takes a little force. Do this gently. There may be a snapping sound.
- The door to the memory card compartment will be freed and should be removable now.
- In other versions of this camera, there is a tab that secures the top from the wrist strap. If yours has this, you won’t be able to completely separate the top until you have removed the top screw in Step 8.
You should now able to remove the top lid of the camera.
Be cautious of the fragile mylar cable that connects the lid to the main body of the camera.
Removing the lid takes a little force. Do this gently. There may be a snapping sound.
The door to the memory card compartment will be freed and should be removable now.
In other versions of this camera, there is a tab that secures the top from the wrist strap. If yours has this, you won’t be able to completely separate the top until you have removed the top screw in Step 8.
Step 6
- Remove the two Phillips #00 screws from the side of the camera.
- Open the small rubber door below this screw that covers the connectors.
Remove the two Phillips #00 screws from the side of the camera.
Open the small rubber door below this screw that covers the connectors.
Step 7
- Open and pivot the LCD screen to its widest open position.
- Remove the rear cover by pulling it straight away from the body of the camera.
- When reassembling the camera, remember to replace the screws in the same location from which you removed them. Otherwise, you may damage the camera.
Open and pivot the LCD screen to its widest open position.
Remove the rear cover by pulling it straight away from the body of the camera.
When reassembling the camera, remember to replace the screws in the same location from which you removed them. Otherwise, you may damage the camera.
Step 8
Front Cover
- Using a Phillips #00 screwdriver, remove the 3.3 mm long top screw located on the side of the camera. This screw holds the side panels and the front cover together.
- The side panel may get stuck on the internal wires, so gently wiggle this panel loose.
Using a Phillips #00 screwdriver, remove the 3.3 mm long top screw located on the side of the camera. This screw holds the side panels and the front cover together.
The side panel may get stuck on the internal wires, so gently wiggle this panel loose.
Step 9
- Gently remove the side panel by pulling it away from the camera.
- The side panel may get stuck on the internal wires, so gently wiggle this panel loose.
Gently remove the side panel by pulling it away from the camera.
Step 10
- Using the Phillips #00 screwdriver, unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel.
Using the Phillips #00 screwdriver, unscrew the 2.4 mm long screw that holds on the front panel underneath the side panel.
Step 11
- Underneath the battery cover there is a 3.8 mm screw in the corner. Using the Phillips #00 screwdriver, remove this screw.
Underneath the battery cover there is a 3.8 mm screw in the corner. Using the Phillips #00 screwdriver, remove this screw.
Step 12
- Gently pull up on the front cover to remove it from the body.
Gently pull up on the front cover to remove it from the body.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 10 other contributors
Travis
Member since: 01/28/2011
238 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 7-31, Regan Winter 2011
Member of Cal Poly, Team 7-31, Regan Winter 2011
CPSU-REGAN-W11S7G31
6 Members
12 Guides authored
