Difficulty
Moderate
Steps
16
Time Required
20 - 30 minutes
Sections
4
- Battery
- 2 steps
- Memory Card
- 1 step
- Outer Case
- 7 steps
- LCD Display
- 6 steps
Flags
0
BackCanon Powershot ELPH 100 HS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Locate the battery cover on the bottom of your camera.
- Slide the tab to the right to open the battery cover.
Locate the battery cover on the bottom of your camera.
Slide the tab to the right to open the battery cover.
1024
Step 2
- Flip the battery cover open.
- Using your fingers, slide the battery out of the camera.
- This was not the original battery that came the camera, so yours may look different.
Flip the battery cover open.
Using your fingers, slide the battery out of the camera.
This was not the original battery that came the camera, so yours may look different.
Step 3
Memory Card
- Push down on the memory card until it clicks and releases.
- Pull up on the memory card to remove it.
Push down on the memory card until it clicks and releases.
Pull up on the memory card to remove it.
Step 4
Outer Case
- Using the Phillips #00 screwdriver, remove the two 3.1mm screws from the bottom of the camera.
- Keep track of all the screws that are being taken out from the outer case.
- The display screen of the camera should be facing towards you.
Using the Phillips #00 screwdriver, remove the two 3.1mm screws from the bottom of the camera.
Keep track of all the screws that are being taken out from the outer case.
The display screen of the camera should be facing towards you.
Step 5
- Ensure that the screen is facing you, and then rotate it till you see the screws on the side of the camera.
- Use the Phillips #00 screwdriver to remove the two 3.1 mm screws.
Ensure that the screen is facing you, and then rotate it till you see the screws on the side of the camera.
Use the Phillips #00 screwdriver to remove the two 3.1 mm screws.
Step 6
- With the screen still facing you, rotate the camera 180 degrees.
- The side with the charging port should now be facing up.
With the screen still facing you, rotate the camera 180 degrees.
The side with the charging port should now be facing up.
Step 7
- Use the Philips #00 screwdriver to pry open the charging port cover.
- Once you pry open the charging port cover, rotate the cover so that you have access to the screw underneath. Which is seen in the next image.
- Remove both 3.1 mm screws using the Phillips #00 screwdriver.
- The image still shows the screw from step 3 in place.
Use the Philips #00 screwdriver to pry open the charging port cover.
Once you pry open the charging port cover, rotate the cover so that you have access to the screw underneath. Which is seen in the next image.
Remove both 3.1 mm screws using the Phillips #00 screwdriver.
The image still shows the screw from step 3 in place.
Step 8
- Turn the camera so the bottom is once again facing up.
- With the battery door still open, use a spudger to remove the cover from the front of the camera.
- Carefully go around all of the edges until the cover is released.
Turn the camera so the bottom is once again facing up.
With the battery door still open, use a spudger to remove the cover from the front of the camera.
Carefully go around all of the edges until the cover is released.
Step 9
- Once the entire front cover has been released carefully pull it off.
- Be careful not to break the tabs that hold it in place.
Once the entire front cover has been released carefully pull it off.
Be careful not to break the tabs that hold it in place.
Step 10
- Just like Step 4-6 , carefully use the Spudger to remove the back cover.
- Go along all the borders of the back cover so that it releases from the camera safely.
- Be careful not to break the tabs.
Just like Step 4-6 , carefully use the Spudger to remove the back cover.
Go along all the borders of the back cover so that it releases from the camera safely.
Be careful not to break the tabs.
Step 11
LCD Display
- Remove the 3.1mm screw on the top-right side of the LCD display screen.
Remove the 3.1mm screw on the top-right side of the LCD display screen.
Step 12
- Use the spudger to carefully separate the screen from the frame.
Use the spudger to carefully separate the screen from the frame.
Step 13
- Use the spudger to lift up the latch on the zero insertion force connector (ZIF).
- Slide the now free ribbon cable from the connector.
Use the spudger to lift up the latch on the zero insertion force connector (ZIF).
Slide the now free ribbon cable from the connector.
Step 14
- Holding the display screen, gently pull the ribbon cable out through the frame of the camera.
Holding the display screen, gently pull the ribbon cable out through the frame of the camera.
Step 15
- Using tweezers, carefully remove the ribbon cable from the connector shown.
Using tweezers, carefully remove the ribbon cable from the connector shown.
Step 16
- The display screen should now be free.
The display screen should now be free.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 3 other contributors
Jacob
Member since: 03/17/2015
540 Reputation
3 Guides authored
Badges:
10
+7 more badges
Team
Michigan Tech, Team 1-10, Lauer Spring 2015
Member of Michigan Tech, Team 1-10, Lauer Spring 2015
MTU-LAUER-S15S1G10
2 Members
5 Guides authored
