Canon Powershot Elph 300Hs Power Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Camera Case
7 steps
Power Button
4 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

BackCanon PowerShot ELPH 300 HS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Safety First

Before you begin taking apart your device, the first, and MOST IMPORTANT STEPS are to:
Turn off your camera.
Remove the battery to prevent risk of shock.

Before you begin taking apart your device, the first, and MOST IMPORTANT STEPS are to:

Turn off your camera.

Remove the battery to prevent risk of shock.

1024

Step 2

              Remove the Battery

Turn off your camera by pressing the power button, located on the top-center of the device.
Locate the battery door on the bottom right area of the camera case.
Place your finger firmly on the black rubber pad on the battery door and slide the door to the right to open it.
Locate the orange battery release button beneath the battery door.
Slide the battery release button downward to release the battery.

Turn off your camera by pressing the power button, located on the top-center of the device.

Locate the battery door on the bottom right area of the camera case.

Place your finger firmly on the black rubber pad on the battery door and slide the door to the right to open it.

Locate the orange battery release button beneath the battery door.

Slide the battery release button downward to release the battery.

Step 3

              Left Side Screws

Be careful when removing screws, as they are stripped easily.
Remove the two screws located on the left side of the camera case, using the Phillips screwdriver #00 (2.0 mm).

Be careful when removing screws, as they are stripped easily.

Remove the two screws located on the left side of the camera case, using the Phillips screwdriver #00 (2.0 mm).

Step 4

              Bottom Screws

Remove the two screws on the bottom of the camera located near the battery door (Phillips #00 screwdriver) (4.0 mm).

Remove the two screws on the bottom of the camera located near the battery door (Phillips #00 screwdriver) (4.0 mm).

Step 5

              Right Side Screws

Remove the screw located on the lower right side of the camera case (Phillips #00 screwdriver) (4.0 mm).
Remove the HDMI A/V out port cover located on the upper right side of the camera.
Remove the screw located just beneath the port cover removed in step 2. (Phillips #00 screwdriver) (2.0 mm).

Remove the screw located on the lower right side of the camera case (Phillips #00 screwdriver) (4.0 mm).

Remove the HDMI A/V out port cover located on the upper right side of the camera.

Remove the screw located just beneath the port cover removed in step 2. (Phillips #00 screwdriver) (2.0 mm).

Step 6

Remove the back portion of the camera case to reveal the screw located on the top of the case.
Remove the screw from the top of camera case, located next to the shutter button (Phillips #00 screwdriver) (1.5 mm).

Remove the back portion of the camera case to reveal the screw located on the top of the case.

Remove the screw from the top of camera case, located next to the shutter button (Phillips #00 screwdriver) (1.5 mm).

Step 7

              Remove the Case from the Camera

Carefully pry the case apart at the seem, using your fingers.
Be careful not to over bend the small metal projections located along the seams. These aid in holding the case together.
Be careful not to allow dust or other particles to settle inside of the camera while the case is detached. This can cause functional issues in the future.

Carefully pry the case apart at the seem, using your fingers.

Be careful not to over bend the small metal projections located along the seams. These aid in holding the case together.

Be careful not to allow dust or other particles to settle inside of the camera while the case is detached. This can cause functional issues in the future.

Step 8

              Power Button

Disconnect the small cable from the yellow port on the motherboard

Disconnect the small cable from the yellow port on the motherboard

Step 9

Disconnect the small cable from the blue port on the motherboard

Disconnect the small cable from the blue port on the motherboard

Step 10

Lift the plastic over the HDMI port on the side of the camera

Lift the plastic over the HDMI port on the side of the camera

Step 11

Lift from the back of the camera, angling forward and pull off to remove the power button assembly

Lift from the back of the camera, angling forward and pull off to remove the power button assembly

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Kathryn Van Susante

Member since: 02/26/2014

667 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Michigan Tech, Team 5-6, Lauer Spring 2014                        

                                                  Member of Michigan Tech, Team 5-6, Lauer Spring 2014 



                    MTU-LAUER-S14S5G6                     


                                            3 Members                     


                                            6 Guides authored

Action Shots#

Needs Better Images#

Introduction#

What you need#

Team#

Action Shots

Needs Better Images

Introduction

What you need

Team