Difficulty

Moderate

Steps

11

Time Required

                          10 minutes

Sections

4

  • Battery
  • 3 steps
  • Back Cover
  • 4 steps
  • Front Cover
  • 3 steps
  • Motherboard Battery
  • 1 step

Flags

0

  • BackCanon PowerShot S410

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Turn the camera with the bottom side facing up.
  • Locate the panel labeled “Batt. Open”
  • Place your finger on the panel and slide it in the direction of the arrow.
  • The slot will swing open revealing the battery pack.

Turn the camera with the bottom side facing up.

Locate the panel labeled “Batt. Open”

Place your finger on the panel and slide it in the direction of the arrow.

The slot will swing open revealing the battery pack.

1024

Step 2

  • Rotate the camera so that the slot is horizontal.
  • Pull the orange lever and the battery will spring out slightly.

Rotate the camera so that the slot is horizontal.

Pull the orange lever and the battery will spring out slightly.

Step 3

  • Grasp battery and fully pull out of slot
  • When placing the new battery back in the slot, the arrow on the battery must align with the arrow on the camera.

Grasp battery and fully pull out of slot

When placing the new battery back in the slot, the arrow on the battery must align with the arrow on the camera.

Step 4

              Back Cover
  • Start by laying the camera flat with the LCD screen facing up.
  • Remove the 3.8mm screw in the upper right corner.

Start by laying the camera flat with the LCD screen facing up.

Remove the 3.8mm screw in the upper right corner.

Step 5

  • Position the camera with the bottom facing up.
  • Remove the 4.8mm screw.
  • Remove the two 2.3mm screws.

Position the camera with the bottom facing up.

Remove the 4.8mm screw.

Remove the two 2.3mm screws.

Step 6

  • Position the camera so that the rubber “AV Out Digital” tab is facing upward.
  • Slide this rubber tab out of the way to reveal the bottom screw.
  • Remove the two 3.7mm screws.

Position the camera so that the rubber “AV Out Digital” tab is facing upward.

Slide this rubber tab out of the way to reveal the bottom screw.

Remove the two 3.7mm screws.

Step 7

  • Turn the camera with the back side facing you.
  • Grip the edges of the back plate, and carefully slide it off.
  • If there is any resistance in movement, double check there are no screws left in the chassis.

Turn the camera with the back side facing you.

Grip the edges of the back plate, and carefully slide it off.

If there is any resistance in movement, double check there are no screws left in the chassis.

Step 8

              Front Cover
  • Orientate the camera as in the picture.
  • Remove the two 2.3mm outer screws.
  • Remove the two 3.8mm screws near the strap bracket.
  • Remove small panel covering mounting bracket.
  • Remove door covering memory card.

Orientate the camera as in the picture.

Remove the two 2.3mm outer screws.

Remove the two 3.8mm screws near the strap bracket.

Remove small panel covering mounting bracket.

Remove door covering memory card.

Step 9

  • Rotate the camera so that the bottom side is facing you.
  • Remove the 3.8mm screw below the mounting bracket.

Rotate the camera so that the bottom side is facing you.

Remove the 3.8mm screw below the mounting bracket.

Step 10

  • Rotate the camera so that the front is facing you.
  • Grasp sides of front cover and carefully pull the front panel off of the camera.

Rotate the camera so that the front is facing you.

Grasp sides of front cover and carefully pull the front panel off of the camera.

Step 11

              Motherboard Battery
  • Position the camera so that the motherboard is facing you.
  • Remove the plastic flap covering the motherboard.
  • Place edge of iPod Opening Tool in the small opening between the battery and the motherboard.
  • Pry the battery off of the motherboard using the iPod Opening Tool.

Position the camera so that the motherboard is facing you.

Remove the plastic flap covering the motherboard.

Place edge of iPod Opening Tool in the small opening between the battery and the motherboard.

Pry the battery off of the motherboard using the iPod Opening Tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Ryan Bolton

Member since: 01/23/2011

307 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 11-27, Maness Winter 2011                        

                                                  Member of Cal Poly, Team 11-27, Maness Winter 2011 



                    CPSU-MANESS-W11S11G27                     


                                            4 Members                     


                                            7 Guides authored