Canon Powershot Sd1000 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Back Panel
5 steps
Front Case
2 steps
LCD Screen
5 steps
Flash Unit
4 steps
Shutter Button
1 step
Lens
8 steps
Motherboard
1 step

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

BackCanon PowerShot SD1000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Back Panel

Remove the two 2.9 mm screws from the side panel closest to the camera lens.

Remove the two 2.9 mm screws from the side panel closest to the camera lens.

1024

Step 2

Remove the two 2.9 mm screws from the camera bottom panel.

Remove the two 2.9 mm screws from the camera bottom panel.

Step 3

Remove the two 2.9 mm screws from the side panel farthest from the lens.

Remove the two 2.9 mm screws from the side panel farthest from the lens.

Step 4

Pull the back panel away from the camera body, starting at the end with the function buttons.

Pull the back panel away from the camera body, starting at the end with the function buttons.

Step 5

Remove the small cover panel and the attached wrist strap mount.

Remove the small cover panel and the attached wrist strap mount.

Step 6

              Front Case

Remove the front cover by gently pulling it away from the camera body.

Remove the front cover by gently pulling it away from the camera body.

Step 7

Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Step 8

              LCD Screen

Remove the two 2.4 mm screws located at the top of the LCD panel.

Remove the two 2.4 mm screws located at the top of the LCD panel.

Step 9

Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

Step 10

Push the metal frame away from the metal tab using the spudger to detach the frame.
Rotate the metal frame upwards.
The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Push the metal frame away from the metal tab using the spudger to detach the frame.

Rotate the metal frame upwards.

The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Step 11

Carefully lift the metal frame from the camera.
Remove the black LCD screen, leaving the thin lens pieces in place.
BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

Carefully lift the metal frame from the camera.

Remove the black LCD screen, leaving the thin lens pieces in place.

BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

Step 12

Carefully pull on the orange connector ribbon to disconnect the LCD screen.
The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.
Tweezers are helpful to disconnect the ribbon.

Carefully pull on the orange connector ribbon to disconnect the LCD screen.

The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

Tweezers are helpful to disconnect the ribbon.

Step 13

              Flash Unit

Slide the metal frame off of the camera on the side that is closest to the flash mechanism.

Slide the metal frame off of the camera on the side that is closest to the flash mechanism.

Step 14

Use a Phillips #00 screwdriver to remove the 2.4 mm screw that secures the flash assembly.

Use a Phillips #00 screwdriver to remove the 2.4 mm screw that secures the flash assembly.

Step 15

Use the spudger to gently and carefully disconnect the flash assembly ribbon from the black connector lock.

Use the spudger to gently and carefully disconnect the flash assembly ribbon from the black connector lock.

Step 16

Pull the flash assembly forward out of the camera to remove it.
BE CAREFUL when handling the flash assembly. Touching the capacitor (the black cylinder attached to the flash assembly) could shock you.

Pull the flash assembly forward out of the camera to remove it.

BE CAREFUL when handling the flash assembly. Touching the capacitor (the black cylinder attached to the flash assembly) could shock you.

Step 17

              Shutter Button

Using the spudger, take off the shutter button by prying the small tab on the front side of the camera.

Using the spudger, take off the shutter button by prying the small tab on the front side of the camera.

Step 18

              Lens

Remove the 2.90mm screw from the lens, near the motherboard.

Remove the 2.90mm screw from the lens, near the motherboard.

Step 19

Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

Step 20

With a spudger disconnect the orange connector ribbon as shown.
Disconnect the orange connector ribbon that is located under the now removed shutter button.

With a spudger disconnect the orange connector ribbon as shown.

Disconnect the orange connector ribbon that is located under the now removed shutter button.

Step 21

Remove the two 2.90 mm screws from the motherboard.

Remove the two 2.90 mm screws from the motherboard.

Step 22

With Tweezers detach the bottom orange ribbon.

With Tweezers detach the bottom orange ribbon.

Step 23

Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

Step 24

With spudger gently remove the Viewfinder Window that is directly above the lens.

With spudger gently remove the Viewfinder Window that is directly above the lens.

Step 25

Detach the mother board with lens from body of camera.
Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.
Your lens has been removed from the motherboard and bottom framing.

Detach the mother board with lens from body of camera.

Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.

Your lens has been removed from the motherboard and bottom framing.

Step 26

              Motherboard

The motherboard (left) is now separated from the lens.

The motherboard (left) is now separated from the lens.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Phillip Phung

Member since: 01/19/2012

555 Reputation

                                      9 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 8-18, Maness Winter 2012                        

                                                  Member of Cal Poly, Team 8-18, Maness Winter 2012 



                    CPSU-MANESS-W12S8G18                     


                                            4 Members                     


                                            10 Guides authored

yakksoho - Mar 5, 2017

Which part is the CCD sensor?

Needs Better Images#

What you need#

Team#

Needs Better Images

What you need

Team