Difficulty
Moderate
Steps
8
Time Required
15 - 25 minutes
Sections
3
- Front and Rear Covers
- 3 steps
- LCD
- 2 steps
- Flash Assembly
- 3 steps
Flags
1
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackCanon PowerShot SD1200 IS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Front and Rear Covers
- Remove the battery.
Remove the battery.
1024
Step 2
- Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)
- Remove the two screws from the bottom of the camera. (4mm Phillips 00)
- Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)
Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)
Remove the two screws from the bottom of the camera. (4mm Phillips 00)
Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)
Step 3
- Pull off the front cover.
- If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.
- Remove the back cover.
Pull off the front cover.
If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.
Remove the back cover.
Step 4
LCD
- Use the spudger to lift the retaining flap on the Zero Insertion Force (ZIF) tab securing the thick ribbon cable.
- Slide out the ribbon cable using fingers or tweezers.
- Be sure you are prying up on the hinged retaining flap, not the connector.
- Using tweezers, disconnect the small ribbon cable below the flash assembly from the No Fuss Connector by simply pulling the ribbon cable straight out.
Use the spudger to lift the retaining flap on the Zero Insertion Force (ZIF) tab securing the thick ribbon cable.
Slide out the ribbon cable using fingers or tweezers.
Be sure you are prying up on the hinged retaining flap, not the connector.
Using tweezers, disconnect the small ribbon cable below the flash assembly from the No Fuss Connector by simply pulling the ribbon cable straight out.
Step 5
- Remove the L shaped brackets from the left and right side of the LCD screen with the spudger tool.
- The Brackets have tabs that need to be pried up.
- Remove the screw below the shutter button. (2.5mm Phillips 00)
- Holding the sides of the LCD screen, lift the screen up and away to remove.
Remove the L shaped brackets from the left and right side of the LCD screen with the spudger tool.
The Brackets have tabs that need to be pried up.
Remove the screw below the shutter button. (2.5mm Phillips 00)
Holding the sides of the LCD screen, lift the screen up and away to remove.
Step 6
Flash Assembly
- Use the spudger to pry up each side of the lens assembly Flat-Topped Connector at the bottom of the motherboard.
- Holding back the lens assembly ribbon cable, use the spudger to lift the Zero Insertion Force (ZIF) connector tab . Slide out the ribbon cable.
- Be sure you are prying up on the hinged retaining flap, not the connector itself.
- Use the spudger to lift the Zero Insertion Force (ZIF) connector tab located on the flash unit. Remove the ribbon cable.
Use the spudger to pry up each side of the lens assembly Flat-Topped Connector at the bottom of the motherboard.
Holding back the lens assembly ribbon cable, use the spudger to lift the Zero Insertion Force (ZIF) connector tab . Slide out the ribbon cable.
Be sure you are prying up on the hinged retaining flap, not the connector itself.
Use the spudger to lift the Zero Insertion Force (ZIF) connector tab located on the flash unit. Remove the ribbon cable.
Step 7
- Remove the two screws (2 mm Phillips 00) along the back edge of the camera frame directly behind the flash assembly.
Remove the two screws (2 mm Phillips 00) along the back edge of the camera frame directly behind the flash assembly.
Step 8
- Lift out the flash assembly.
Lift out the flash assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Jeff Casper
Member since: 09/15/2016
848 Reputation
7 Guides authored
Badges:
18
+15 more badges
Team
USF Tampa, Team 17-5, Blackwell Fall 2016
Member of USF Tampa, Team 17-5, Blackwell Fall 2016
USFT-BLACKWELL-F16S17G5
3 Members
7 Guides authored
