Canon Powershot Sd1200 Is Lcd Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Front and Rear Covers
3 steps
LCD
2 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

BackCanon PowerShot SD1200 IS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front and Rear Covers

Remove the battery.

Remove the battery.

1024

Step 2

Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)
Remove the two screws from the bottom of the camera. (4mm Phillips 00)
Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)

Remove the two screws from the bottom of the camera. (4mm Phillips 00)

Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

Step 3

Pull off the front cover.
If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.
Remove the back cover.

Pull off the front cover.

If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.

Remove the back cover.

Step 4

LCD

Use the spudger to lift the retaining flap on the Zero Insertion Force (ZIF) tab securing the thick ribbon cable.
Slide out the ribbon cable using fingers or tweezers.
Be sure you are prying up on the hinged retaining flap, not the connector.
Using tweezers, disconnect the small ribbon cable below the flash assembly from the No Fuss Connector by simply pulling the ribbon cable straight out.

Use the spudger to lift the retaining flap on the Zero Insertion Force (ZIF) tab securing the thick ribbon cable.

Slide out the ribbon cable using fingers or tweezers.

Be sure you are prying up on the hinged retaining flap, not the connector.

Using tweezers, disconnect the small ribbon cable below the flash assembly from the No Fuss Connector by simply pulling the ribbon cable straight out.

Step 5

Remove the L shaped brackets from the left and right side of the LCD screen with the spudger tool.
The Brackets have tabs that need to be pried up.
Remove the screw below the shutter button. (2.5mm Phillips 00)
Holding the sides of the LCD screen, lift the screen up and away to remove.

Remove the L shaped brackets from the left and right side of the LCD screen with the spudger tool.

The Brackets have tabs that need to be pried up.

Remove the screw below the shutter button. (2.5mm Phillips 00)

Holding the sides of the LCD screen, lift the screen up and away to remove.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Jeff Casper

Member since: 09/15/2016

848 Reputation

                                      7 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       USF Tampa, Team 17-5, Blackwell Fall 2016                        

                                                  Member of USF Tampa, Team 17-5, Blackwell Fall 2016 



                    USFT-BLACKWELL-F16S17G5                     


                                            3 Members                     


                                            7 Guides authored

Killer King - Aug 3, 2020

Hello do you guys sello the LCD screen and do you ship to México.

Slice and Dice#

Introduction#

What you need#

Team#

Slice and Dice

Introduction

What you need

Team