Canon Powershot Sd1400 Is Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Screen
14 steps

Flags

BackCanon PowerShot SD1400 IS
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Remove the 2.0 mm Phillips screws on both sides of the camera using the Phillips #00 screwdriver.
There will be 4 total screws that need to be removed, 2 on each side.

Remove the 2.0 mm Phillips screws on both sides of the camera using the Phillips #00 screwdriver.

There will be 4 total screws that need to be removed, 2 on each side.

1024

Step 2

Remove the 4.0 mm Phillips screw located on the bottom of the camera.

Remove the 4.0 mm Phillips screw located on the bottom of the camera.

Step 3

Remove the front face panel of the camera.
The face can be removed by hand with a firm pressure. If one point of the face is stuck to the body, ensure that there is not a screw remaining at that position to hold it in place.

Remove the front face panel of the camera.

The face can be removed by hand with a firm pressure. If one point of the face is stuck to the body, ensure that there is not a screw remaining at that position to hold it in place.

Step 4

Remove the rear panel of the camera.

Remove the rear panel of the camera.

Step 5

Remove the panel of buttons by hand.

Remove the panel of buttons by hand.

Step 6

Remove the 3.0 mm Phillips copper colored screw from the top of the camera.

Remove the 3.0 mm Phillips copper colored screw from the top of the camera.

Step 7

Remove the 3.0 mm Phillips silver screw from the rear face of the camera, located on the upper right corner.

Remove the 3.0 mm Phillips silver screw from the rear face of the camera, located on the upper right corner.

Step 8

Using the plastic spudger, pry the golden film on the front face of the camera off of the microchip.
Once removed, a silver screw will be visible from underneath the golden film.

Using the plastic spudger, pry the golden film on the front face of the camera off of the microchip.

Once removed, a silver screw will be visible from underneath the golden film.

Step 9

Remove the 3.0 mm Phillips silver screw using the screwdriver.

Remove the 3.0 mm Phillips silver screw using the screwdriver.

Step 10

Using the metal spudger, carefully pry the small black tab away from the brown film end of the golden film.
Once released, the small black tab will point straight away from the front face of the camera.
After releasing the tab, the golden film will no longer be secured to the front face of the camera.

Using the metal spudger, carefully pry the small black tab away from the brown film end of the golden film.

Once released, the small black tab will point straight away from the front face of the camera.

After releasing the tab, the golden film will no longer be secured to the front face of the camera.

Step 11

Unplug the small chip from the face of the camera by carefully inserting the metal spudger underneath the cluster of red wires visible. Then lift the cluster of wires upwards, parallel to the front face of the camera.

Unplug the small chip from the face of the camera by carefully inserting the metal spudger underneath the cluster of red wires visible. Then lift the cluster of wires upwards, parallel to the front face of the camera.

Step 12

You can now remove the top panel from the camera using your hands with firm pressure.

You can now remove the top panel from the camera using your hands with firm pressure.

Step 13

Insert the metal spudger underneath the golden film on the front face
Lift the golden film on the front face of the camera up and away from its connection

Insert the metal spudger underneath the golden film on the front face

Lift the golden film on the front face of the camera up and away from its connection

Step 14

Remove the screen by sliding the golden film out of the channel and pulling the screen away from the camera.

Remove the screen by sliding the golden film out of the channel and pulling the screen away from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 4 other contributors

                    Braxton Beal

Member since: 01/30/2018

681 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Baylor, Team S1-G3, Johnson Spring 2018                        

                                                  Member of Baylor, Team S1-G3, Johnson Spring 2018 



                    BU-JOHNSON-S18S1G3                     


                                            3 Members                     


                                            4 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team