Difficulty
Easy
Steps
11
Time Required
5 minutes
Sections
3
- Battery
- 2 steps
- Front and Rear Casing
- 7 steps
- Wrist Strap Mount
- 2 steps
Flags
0
BackCanon PowerShot SD500 Digital ELPH
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Slide open the battery cover.
- Push the small orange tab to the side so the battery can be removed.
Slide open the battery cover.
Push the small orange tab to the side so the battery can be removed.
1024
Step 2
- Slide the battery out of the battery compartment.
Slide the battery out of the battery compartment.
Step 3
Front and Rear Casing
- Two Phillips screws need to be removed using a #00 Phillips screwdriver. The upper screw is under the USB port cover, which can simply be pulled away gently from the casing. the lower screw is visible on the panel.
- The screws are different sizes. The .125 inch screw is located under the USB port cover. The 0.85 inch screw goes in the lower hole on the panel.
- When looking at the back of the camera, these two screws are on the right panel of the camera.
Two Phillips screws need to be removed using a #00 Phillips screwdriver. The upper screw is under the USB port cover, which can simply be pulled away gently from the casing. the lower screw is visible on the panel.
The screws are different sizes. The .125 inch screw is located under the USB port cover. The 0.85 inch screw goes in the lower hole on the panel.
When looking at the back of the camera, these two screws are on the right panel of the camera.
Step 4
- Remove the right side cover from the camera casing.
Remove the right side cover from the camera casing.
Step 5
- Remove a .07 inch Phillips screw using a #00 Phillips screwdriver.
Remove a .07 inch Phillips screw using a #00 Phillips screwdriver.
Step 6
- Remove two .085 inch Phillips screws from the left side of the camera using a #00 Philips screwdriver.
Remove two .085 inch Phillips screws from the left side of the camera using a #00 Philips screwdriver.
Step 7
- Remove the left side cover from the camera.
Remove the left side cover from the camera.
Step 8
- Remove three .15 inch Phillips screws from the bottom of the camera using a #00 Phillips screwdriver.
Remove three .15 inch Phillips screws from the bottom of the camera using a #00 Phillips screwdriver.
Step 9
- Once the casing is unscrewed, hold the camera with one side facing down, and lift the opposite face of the casing to open it.
- Remove the internal camera components and layout out all pieces on a clean surface.
- The front and back cover may require gentle rocking to remove.
Once the casing is unscrewed, hold the camera with one side facing down, and lift the opposite face of the casing to open it.
Remove the internal camera components and layout out all pieces on a clean surface.
The front and back cover may require gentle rocking to remove.
Step 10
Wrist Strap Mount
- Unscrew two Phillips screws using a #00 Phillips screwdriver from front cover of the camera.
Unscrew two Phillips screws using a #00 Phillips screwdriver from front cover of the camera.
Step 11
Remove Mount
- Remove plastic cover from front side of camera.
- Remove and pull away wrist strap mount from the front side of the camera.
Remove plastic cover from front side of camera.
Remove and pull away wrist strap mount from the front side of the camera.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Kimberly Saeger
Member since: 10/13/2014
101 Reputation
1 Guide authored
Badges:
2
Team
Clemson, Team 2-1, Benson Fall 2014
Member of Clemson, Team 2-1, Benson Fall 2014
CLEM-BENSON-F14S2G1
4 Members
9 Guides authored
